BUFFALO MONITOR for the CME11E9-EVBU BOARD MANUAL START-UP Applying power to the EVB causes a Power On Reset (POR) to occur. This POR condition causes the MCU and user I/O port circuitry to be reset, and the monitor invoked. Both COM ports will display the following EVB monitor prompt: BUFFALO 3.4(ext) - Motorola Bit User Fast Friendly Aid to Logical Operation If the EVB monitor prompt is not displayed (as shown above), press the user reset switch SWl. If the EVB monitor prompt cannot be displayed, the following steps are to be performed. a. Disconnect EVB power source. b. Check all EVB cabling and power connections. c. Check hardware options and preparation procedures. d. Check all EVB components for proper PCB placement. e. Check PC baud rate and terminal software setup for 9600 baud, 8 bits, 1 stop, no parity. f. If using External Programmed version of Buffalo, I/O ports B and C are not available to the user. Ports B and C become address and data bus ports in expanded mode operation. MONITOR PROGRAM INTRODUCTION This chapter provides the overall description of the monitor program. This description will enable the user to understand the basic structure of the program, and to modify or customize the program for specific applications. PROGRAM DESCRIPTION The monitor program supplied for the EVB is called BUFFALO (Bit User Fast Friendly Aid to Logical Operations). This program communicates via the R65C51 Asynchronous Communications Interface Adapter (ACIA) device and the MCU Serial Communications Interface (SCI). The EVB monitor program is contained in EPROM (external to the MCU). MCUs supplied with the EVB kit have the configuration (CONFIG) register ROMON bit cleared thereby disabling the MCU internal ROM. Having the monitor program in EPROM external to the MCU at locations $EOOO-$FFFF is a great advantage because it allows the user to add instructions to customize the monitor for specific requirements. The main module of the monitor program includes all the parts required by any of the individual command modules. Therefore the main module is a kernel of the BUFFALO monitor program, and consists of five parts which are as follows: a. Initialization b. Command interpreter c. I/O routines d. Utility subroutines e. Command table INITIALIZATION This part of the main module contains all of the reset initialization code. In this section, internal RAM locations are set up, and the I/O channels for the terminal is set up. To set up the terminal I/O port, BUFFALO must determine if the terminal is connected to the SCI or to the external ACIA. This is accomplished by sending a sign-on message to both ports and then waiting for response from either port. When BUFFALO recognizes a carriage return from either port, that port is then used for all subsequent terminal I/O operations. The 68HC11 Port E0 pin is used as an Auto-Start signal in the Buffalo version 3.4 (ext). This pin has a 10K pull-down resistor attached to maintain a low level. A high level applied to the pin at RESET will vector the Buffalo operation to start execution at the beginning of internal 68HC11 EEprom (address $B600). The user must have loaded executable machine code at this location or operation is not determined. The Buffalo executes no initialization operations if the Auto-Start is used, All initialization must be performed by the user's code. Note that the Port E0-3 bits are also used for the keypad port on the board. COMMAND INTERPRETER The next section of the main module is the command interpreter. American Standard Code for Information Interchange (ASCII) characters are read form the terminal into the input buffer until a carriage return or a slash (/) is received. The command field is then parsed out of the input buffer and placed into the command buffer. A table of commands is then searched and if a match is found, the corresponding command module is called as a subroutine. All commands return back to the command interpreter upon completion of the operation. I/O ROUTINES The I/O section of the main module consists of a set of supervisor routines, and three sets of driver routines. The supervisor routines are INIT, INPUT, and OUTPUT. These routines determine which driver subroutine to call to perform the specific action. Each set of driver routine consists of an initialization routine, an input routine, and an output routine. One set of drivers is for the SCI port and these routines are called ONSCI, INSCI, and OUTSCI. The second set of drivers is for the ACIA and these routine ar called ONACIA, INACIA, and OUTACIA. All I/O communications are controlled by three RAM locations (IODEV, EXTDEV, and HOSTDEV). EXTDEV specifies the external device type (0=none, l=ACIA). HOSTDEV specifies which I/O port is used for host communications (O=SCI, 1=ACIA). IODEV instructs the supervisor routine which port/driver routine to use (0=SCI, 1=ACIA). The INIT routines set up a serial transmission format of eight data bits, two stop bits, and no parity. For the SCI, the baud rate is set to 9600 for an 8MHz crystal (2 MHz E-clock). The ACIA is also initialized to 9600 baud. To achieve a different baud rate the baud rate control registers can be modified using the MM command. For the SCI, this means modifying address $102B (refer to MCU data sheet, SCI baud rate selection). For the ACIA refer to the board R65C51 data sheet in the appendix. The INPUT routine reads from the specified port. If a Character is received, the character is returned in accumulator A. If no character is received a zero (0) is returned in accumulator A. This routine does not wait for a character to be received before returning (this function performed by the INCHAR subroutine). The OUTPUT routine takes the ASCII character loaded in accumulator A and writes to the specified I/O port. This routine waits until the character is transmitted before returning. UTILITY SUBROUTINE Several subroutines exist that are available for performing I/O tasks. A jump table has been set up in ROM directly beneath the interrupt vectors. To use these subroutines, execute a jump to subroutine (JSR) command to the appropriate entry in the jump table. By default, all I/O performed with these routines are sent to the terminal port. Redirection of the I/O port is achieved by placing the specified value (O=SCI, 1=ACIA)into RAM location IODEV. Utility subroutines available to the user are as follows: UPCASE If character in accumulator A is lower case alpha, convert to upper case. WCHEK Test character in accumulator A and return with Z bit set if character is whitespace (space, comma, tab). DCHEK Test character in accumulator A and return with Z bit set if character is delimiter (carriage return or whitespace). INIT Initialize I/O device. INPUT Read I/O device. OUTPUT Write I/O device. OUTLHLF Convert left nibble of accumulator A contents to ASCII and output to terminal port. OUTRHLF Convert right nibble of accumulator A contents to ASCII and output to terminal port. OUTA Output accumulator A ASCII character. OUTlBYT Convert binary byte at address in index register X to two ASCII characters and output. Returns address in index register X pointing to next byte. OUTlBSP Convert binary byte at address in index register X to two ASCII characters and output followed by a space. Returns address in index register OUT2BSP Convert two consecutive binary bytes starting at address in index register X to four ASCII characters and output followed by a space. Returns address in index register X pointing to next byte. OUTCCRLF Output ASCII carriage return followed by a line feed. OUTSTRG Output string of ASCII bytes pointed to by address in index register X until character is na end of transmission ($04). OUTSTRGO Same as OUTSTRG except leading carriage return and line feed is skipped. INCHAR Input ASCII character to accumulator A and echo back. This routine loops until character is actually received. Utility jump subroutines for performing I/O tasks are shown below. These subroutines are in ROM and are programmed as jumps. To use the jump subroutine, execute a JSR to the applicable address shown below. $FFAO JMP UPCASE Convert character to uppercase $FFA3 JMP WCHEK Test character for whitespace $FFA6 JMP DCHEK Check character for delimiter $FFA9 JMP INIT Initialize I/O device $FFAC JMP INPUT Read I/O device $FFAF JMP OUTPUT Write I/O device $FFB2 JMP OUTLHLF Convert left nibble to ASCII and output $FFB5 JMP OUTRHLF Convert right nibble to ASCII and output $FFB8 JMP OUTA Output ASCII character $FFBB JMP OUTlBYT Convert binary byte to 2 ASCII characters and output $FFBE JMP OUT1BSP Convert binary byte to 2 ASCII characters and output followed by space $FFCl JMP OUT2BSP Convert 2 consecutive binary bytes to 4 ASCII characters and output followed by space. $FFC4 JMP OUTCRLF Output ASCII carriage return followed by line feed $FFC7 JMP OUTSTRG Output ASCII string until end of transmission ($04) $FFCA JMP OUTSTRGO Same as OUTSTRG except leading carriage return and line fees is skipped $FFCD JMP INCHAR Input ASCII character and echo back COMMAND TABLE The command table consists of three lines for each entry. The first byte is the number of characters in the command name. The second entry is the ASCII command name. The third entry is the starting address of the command module. As and example: FCB 3 3 characters in command name FCC 'ASM' ASCII literal command name string FDB #ASM Jump address for command module Each command in the BUFFALO program is a individual module. Thus, to add or delete commands, all that is required is to include a new command table. INTERRUPT VECTORS Interrupt vectors residing in MCU internal Rom are accessible as follows. Each vector is assigned a three byte field residing in EVB memory map locations $0000-$0100. This is where the monitor program expects the MCU RAM to reside. Each vector points to a three byte field which is used as a jump table to the vector service routine. The following Table lists the interrupt vectors and associated three byte field. Interrupt Vector Jump Table INTERRUPT VECTOR FIELD Serial communications Interface (SCI) $00C4-$00C6 Serial Peripheral Interface (SPI) $00C7-$00C9 Pulse Accumulator Input Edge $00CA-$00CC Pulse Accumulator Overflow $00CD-$00CF Timer Overflow $00DO-$00D2 Timer Output Compare 5 $00D3-$00D5 Timer Output Compare 4 $00D6-$00D8 Timer Output Compare 3 $00D9-$00DB Timer Output Compare 2 $00DC-$00DE Timer Output Compare 1 $00DF-$00E1 Timer Input Capture 3 $00E2-$00E4 Timer Input Capture 2 $00E5-$00E7 Timer Input Capture 1 $00E8-$00EA Real Time Interrupt $00EB-$00ED IRQ $00EE-$00FO XIRQ $00F1-$00F3 Software Interrupt (SWI) $00F4-$00F6 Illegal Opcode $00F7-$00F9 Computer Operating Properly (COP) $00FA-$00FC Clock Monitor $00FD-$00FF To use vectors specified in the table, the user must insert a jump extended opcode in the byte field of the vector required. For an example, for the IRQ vector, the following is performed: a. Place $7E (JMP) at location $00EE. b. Place IRQ service routine address at locations $00EF and $00F0. $00EE 7E 80 00 JMP IRQ SERVICE OPERATING INSTRUCTIONS INTRODUCTION This chapter provides the necessary information to initialize and operate the EVB in a target system environment. Information consists of the control switch description, operating limitations, command line format, monitor commands, and operating procedures. The operating procedures consist of assembly/disassembly and downloading descriptions and examples. RESET SWITCH The EVB contains a user reset switch Sl. This switch is a momentary action push-button switch that resets the EVB MCU circuits. LIMITATIONS CAUTION Caution should be observed when programming or erasing MCU EEPROM locations. EVB MCU configuration (CONFIG) register ROMON bit is cleared to disable MCU internal ROM, thereby allowing external EPROM containing the BUFFALO program to control EVB operations. The MC68HC11 MCU SCI has been set for 9600 baud using a 2 MHz E clock external bus. This baud rate can be changed by software by re-programming the BAUD register in the ONSCI subroutine of the BUFFALO monitor program. As the RS-232C handshake lines are not used on the COM1 SCI port, a delay of approximately 300 milliseconds is present between successive characters sent to terminal computer during the execution of the LOAD T command in the monitor program. The monitor program uses the MCU internal RAM located at $0036- $00FF. The control registers are located at $1000-$103F. The monitor program also uses Output Compare 5 (OC5) and XIRQ for the TRACE instruction, therefore OC5 and XIRQ should not be used in user routines being traced. Jumper JP13 should be installed to enable this operation. The EVB allows the user to use all the features of the BUFFALO evaluation software, however it should be noted (when designing code) that the BUFFALO uses the MCU on-chip RAM locations $0036- $00FF leaving only 54 bytes for the user (i.e., $0000-$0035). However, external ram is normally available from address $100 to $7FFF depending on the size of ram installed. OPERATING PROCEDURES The EVB is a simplified debugging/evaluating tool designed to operate in either the debugging or evaluation (emulation) mode of operation. DEBUGGING MODE The first mode of operation allows the user to debug user code under control of the monitor program. User code can be assembled in one of two methods. THe first method is to assemble code using the line assembler in the BUFFALO monitor program via the EVB user RAM ($0100 to $1FFF or $2000-$3FFF). The second method is to assemble code on a host computer and then download the code to the EVB user RAM via Motorola S-records. The monitor program is then used to debug the assembled user code. Having the monitor program in EPROM external to the MCU ($E000-$FFFF) allows the user to add instructions to customize the monitor for specific requirements. EVALUATION MODE The second mode of operation allows the user to evaluate (emulate) user code in a target system environment utilizing the memory of the MC68HC11 MCU. This is accomplished by relocating the code from locations $0100-$1FFFF or $2000-$3FFF (EVB user RAM) to $E000-$FFFF (MCU 8k ROM). MCU locations $0000-$00FF (RAM) and $B600-$B7FF (EEPROM) are also available to the user. The EVB then emulates an EPROM equivalent of the masked ROM device in the single chip mode of operation. MONITOR PROGRAM The monitor BUFFALO program is the resident firmware for the EVB, which provides a self contained operating environment. The monitor interacts with the user through predefined commands that are entered from a terminal. The user can use any of the commands supported by the monitor. A standard input routine controls the EVB operation while the user types a command line. Command processing begins only after the command line has been terminated by depressing the keyboard carriage return (Return) key. COMMAND LINE FORMAT The command line format is as follows: > [](RETURN) where: > EVB monitor prompt. Command mnemonic(single letter for most commands). Expression or address. (RETURN) RETURN keyboard key - depressed to enter command. NOTES: (1) The command line format is defined using special characters which have the following syntactical meanings: < > Enclose syntactical variable [ ] Enclose optional fields [ ]... Enclose optional fields repeated These characters are not entered by the used, but are for definition purposes only. (2) Fields are separated by any number space, comma, or tab characters. (3) All input numbers are interpreted as hexadecimal. (4) All input commands can be entered either upper or lower case lettering. All input commands are converted automatically to upper case lettering except for downloading commands sent to the host computer, or when operating in the transparent mode. (5) A maximum of 35 characters may be entered on a command line. After the 36th character is entered, the monitor automatically terminates the command entry and the terminal CRT displays the message "Too Long". (6) Command line errors may be corrected by backspacing (CTRL-H) or by aborting the command (CTRL-X or DELETE). (7) After a command has been entered, pressing (RETURN) a second time will repeat the command. MONITOR COMMANDS The monitor BUFFALO program commands are listed alphabetically by mnemonic in Table 1. Each of the commands are described in detail following the tabular command listing. Additional terminal keyboard functions are as follows: (CTRL)A Exit transparent mode or assembler (CTRL)B Send break command to host in transparent mode (CTRL)H Backspace (CTRL)J Line feed <1f> (CTRL)W Wait/freeze screen (Note 1) (DELETE) Abort/cancel command (RETURN) Enter command/repeat last command NOTES: (1) Execution is restarted by any terminal keyboard key. (2) When using the control key with a specialized command such as (CTRL)A, the (CTRL) key is depressed and held, then the A key is depressed. Both keys are then released. Command line input examples in this chapter are amplified with the following: Underscore entries are user-entered on the terminal keyboard. Command line input is entered when the keyboard (RETURN) key is depressed. Typical example of this explanation is as follows: >MD F000 F100 TABLE 1. Monitor Program Commands COMMAND DESCRIPTION ASM [
] Assembler/disassembler BF Block fill memory with data BR [-] [
]... Breakpoint set BULK Bulk erase EEPROM BULKALL Bulk erase EEPROM + CONFIG register CALL [
] Execute subroutine G [
] Execute program HELP Display monitor commands LOAD Download (S-records*) via host port LOAD Download (S-records*) via terminal port MD [ []] Dump memory to terminal MM [
] Memory modify MOVE [,dest>] Move memory to new location P Proceed/continue from breakpoint RM[p,y,x,a,b,c,s,] Register modify T [] Trace $1-$FF instructions TM Enter transparent mode VERIFY Compare memory to download data via host port VERIFY Compare memory to download data via terminal port NOTE: *Refer to Appendix A for S-record information. Table 2 lists the compatible commands that are applicable to all revisions of the BUFFALO monitor program. In most cases the initial single letter of the command mnemonic or a specific symbol (shown below) can be used. A minimum number of characters must be entered to at least guarantee uniqueness from other commands (i.e., MD = MOVE, ME = MEMORY). TABLE 2, Monitor Program Compatible Commands EVB COMMAND COMPATIBLE COMMANDS ASM [
] ASSEM BF FILL BR [-] [
]... BREAK BULK BULK BULKALL BULKA CALL [
] CALL G [
] GO HELP HELP, ? LOAD LOAD LOAD LOAD MD [ []] DUMP MM [
] MEMORY, / MOVE [] MOVE P PROCEED RM [P,X,Y,A,B,C,S,] REGISTER T [] TRACE TM HOST VERIFY VERIFY VERIFY VERIFY ASM Assembler/Disassembler ASM ASM [
] where:
is the starting address for the assembler operation. Assembler operation defaults to internal RAM if no address if given. The assembler/disassembler is an interactive assembler/editor. Each source line is converted into the proper machine language code and is stored in memory overwriting previous data on a line-by-line basis at the time of entry. In order to display and instruction, the machine code is disassemble and the instruction mnemonic and operands are displayed. All valid opcodes are converted to assembly language mnemonics. All invalid opcodes are displayed on the terminal CRT as "ILLOP". The syntax rules for the assembler are as follows: (a.) All numerical values are assumed to be hexadecimal. Therefore no base designators (e.g., $ + hex, % + binary, etc.) are allowed. (b.) Operands must be separated by one or more space or tab characters. (c.) Any characters after a valid mnemonic and associated operands are assumed to be comments and are ignored. Addressing modes are designed as follows: (a.) Immediate addressing is designated by preceding the address with a # sign. (b.) Indexed addressing is designated by a comma. The comma must be preceded a one byte relative offset (even if the offset is 00), and the comma must be followed by an X or Y designating which index register to use (e.g., LDAA 00,X). (c.) Direct and extended addressing is specified by the length for the address operand (1 or 2 digits specifies direct, 3 or 4 digits specifies extended). Extended addressing can be forced by padding the address operand with leading zeros. (d.) Relative offsets for branch instructions are computed by the assembler. Therefore the valid operand for any branch instruction is the branch-if-true address, not the relative offset. When a new source line is assembled, the assembler overwrites what was previously in memory. If no new source line is submitted, or if there is an error in the source line, then the contents of memory remain unchanged. Each of the instruction pairs Arithmetic Shift Left (ASL)/Logical Shift Left (LSL) have the same opcode, so disassembly always displays the ASL mnemonic. If the assembler tries to assemble at an address that is not in RAM, an invalid address message "rom-xxx" is displayed on the terminal CRT (xxxx = invalid address.) Assembler/disassembler subcommands are as follows. If the assembler detects an error in the new source line, the assembler will output an error message and then reopen the same address location. / Assemble the current line and then disassemble the same address location. ^ Assemble the current line and then disassemble the previous sequential address location. (RETURN) Assemble the current line and then disassemble the next opcode address. (CTRL)J Assemble the current line. If there isn't a new line to assemble, then disassemble the next sequential address location. Otherwise, disassemble the next opcode address. (CTRL)A Exit the assembler mode of operation. EXAMPLES DESCRIPTION >ASM 0200 Immediate mode addressing, requires, # before 0200 STOP $FFFF operand. >LDAA #55 86 55 0202 STOP $FFFF Direct mode addressing. >STAA C0 97 C0 0204 STOP $FFFF Index mode, if offset = 0 (,X) will not be >LDS 0,X accepted. AE 00 0206 STOP $FFFF Branch out of range message. >BRA 0230 Branch out of range 0206 STOP $FFFF Branch offsets calculated automatically, >BRA 0230 address required as conditional branch operand. 20 28 0208 STOP $FFFF >(CTRL)A Assembler operation terminated. > Refer to the end of this chapter for additional operational information pertaining to the use of the assembler/disassembler. BF Block Fill BF Block Fill BF where: Lower limit for fill operation. Upper limit for fill operation. Fill pattern hexadecimal value. The BF command allows the user to repeat a specific byte throughout a determined user memory range. If an invalid address is specified, an invalid address is specified, an invalid address message "rom-xxxx" is displayed on the terminal CRT (xxxx = invalid address). EXAMPLES DESCRIPTION >BF 0200 0230 FF Fill each byte of memory from 0200 through 0230 with data pattern FF. >BF 0200 0200 0 Set location 0200 to 0. BR Breakpoint Set BR Breakpoint Set BR [-][
]... where: [-] by itself removes (clears) all breakpoints. [-] proceeding [ Set breakpoint. BR ... Set several breakpoints. BR - Remove all breakpoints. BR - ... Remove and add . BR - ... Add , clear all entries, then add . BR -... Add , then remove addr2>. BR Breakpoint Set BR EXAMPLES DESCRIPTION >BR 0203 Set breakpoint at address location 0203. 0203 0000 0000 0000 > >BR 0203 0205 0207 0209 Sets four breakpoints. Breakpoints at same address will result in only one 0203 0205 0207 0209 breakpoint being set. > >BR Display all current breakpoints. 0203 0205 0207 0209 > >BR - 0209 Remove breakpoint at address location 0209. 0203 0205 0207 0000 > >BR 0209 - Clear breakpoint table and add C009. 0209 0000 0000 0000 > >BR - Remove all breakpoints. 0000 0000 0000 0000 > >BR E000 Only RAM locations can be breakpointed. rom-E000 Invalid Address message. 0000 0000 0000 0000 > >BR 0205 0207 0209 0211 0213 Maximum of four breakpoints cam be set. Full Buffer full message. 0205 0207 0209 0211 > BULK BULK ERASE EEPROM BULK The bulk command allows the user to erase all MCU EEprom locations ($B600-$B7FF). A delay loop is built in such that the erase time is about 5ms when running at 2 MHz E clock. This command is only applicable for A38P and A95J mask sets, and all future mask sets. NOTE No erase verification message will be displayed upon completion of the bulk EEPROM erase operation. User must verify erase operation by examining one or two EEPROM locations using the MM or MD command. EXAMPLE DESCRIPTION >BULK Bulk erase all MCU EEPROM locations ($B600-$B7FF). > Prompt indicates erase sequence completed. BULKALL BULK ERASE EEPROM AND CONFIG REGISTER BULKALL The bulkall command allows the user to erase all MCU EEPROM locations ($B600-$B7FF) including the configuration (CONFIG) register location ($103F). A delay loop is built in such that the erase time is about 5 ms when running at 2 MHz E Clock. NOTE No erase verification message will be displayed upon completion of the bulkall EEPROM and configuration register erase operation. User must verify erase operation by examining one or two EEPROM locations/configuration register location using the MM or MD command. CAUTION Caution should be observed when erasing MCU EEPROM locations. EVB MCU configuration (CONFIG) register ROMON bit is cleared to disable MCU internal ROM, thereby allowing external EPROM containing the BUFFALO program to control EVB operations. EXAMPLE DESCRIPTION >BULKALL Bulk erase all MCU EEPROM ($B600-$B7FF) and configuration register ($103F) locations. > Prompt indicates erase sequence completed. CALL GOTO SUBROUTINE CALL [
] where:
is the starting address where user program subroutine execution begins. The CALL command allows the user to execute a user program subroutine. Execution starts at the current program counter (PC) address location , unless a starting address is specified. Two extra bytes are placed onto the stack before the return from interrupt (RTI) is issued so that the first unmatched return from subroutine (RTS) encountered will return control back to the monitor program. Thus any user program subroutine can be called and executed via the monitor program. Program execution continues until a breakpoint encountered, or the EVB reset switch S1 is activated (pressed). EXAMPLE PROGRAM CALL, G, AND P COMMAND EXAMPLES >ASM 0200 0206 STX $FFFF >NOP 0200 STX $FFF 01 >LDAA #44 0207 STX $FFFF 86 44 >NOP 0202 STX $FFFF 01 >STAA 07FC 0208 STX $FFFF B7 07 FC >RTS 0205 STX $FFFF 39 >NOP 0209 STX $FFFF 01 >(CTRL)A EXAMPLE DESCRIPTION >CALL 0200 Execute program subroutine. P-0200 Y-DEFE X-F4FF A-44 B-FE C-D0 S-004A Displays status of registers at time RTS encountered (except P register contents). GO GO TO PROGRAM EXECUTION G [
] where:
is the starting address where user program execution (free run in real time). The user may optionally specify a starting address where execution is to begin. Execution starts at the current program counter (PC) address location, unless a starting address is specified. Program execution continues until a breakpoint us encountered, or the EVB reset switch S1 is activated (pressed). NOTE Refer to example program shown and insert breakpoints at locations $0205 and $0207 for the following G command example. EXAMPLE DESCRIPTION >$0200 Begin program execution at PC address location 0200. P-0205 Y-0000-X-00CD A-44 B-FB C-DO S-004A Breakpoint encountered at 0205. HELP The HELP command enables the user available EVB command information to be displayed on the terminal CRT for quick reference purposes. EXAMPLE >HELP ASM [
] Line assembler/disassembler. / Do same address. ^ Do previous address. CTRL-J Do next address RETURN Do next opcode. CTRL-A Quit. BF [>data>] Block fill BR [-] [] Set up breakpoint table. BULK Erase the EEPROM> BULKALL Erase EEPROM and CONFIG> CALL [] Call user subroutine. G [] Execute user code. LOAD, VERIFY or Load or verify S-records. MD [] [addr2>]] Memory dump. MM [] Memory modify / Open same address. CTRL-H or A Open previous addr. CTRL-J Open next addr. SPACE Open next addr. RETURN Quit. 0 Compute offset to MOVE [] Block move. P Proceed/continue execution. RM [P,Y,X,A,B,C, OR S] Register modify. T[] Trace n instructions. TM Transparent mode (CTRL-A = exit, CTRL B= send break). CTRL-H Backspace. CTRL-W Wait for any key. CTRL-X or DELETE Abort/cancel command. RETURN Repeat last command. > LOAD LOAD S-RECORD LOAD LOAD where: download S-records to EVB via host port. download S-records to EVB via terminal port. The LOAD command moves (downloads) object data in S-record format (see Appendix A) from an external host computer to EVB. As the EVB monitor processes only valid S-record data, it is possible for the monitor to hang up during a load operation. If an S-record starting address points to and invalid memory location, the invalid address message "error addr xxxx" is displayed on the Terminal CRT (xxxx = invalid address). EXAMPLES DESCRIPTION >LOAD cat trial.out LOAD command entered to download data from host cat trail.out computer to EVB via host port. done > >LOAD cat trial.out LOAD command entered. cat trial.out error addr E000 Invalid address message. > S-records must be downloaded into RAM. Refer to the downloading procedures at the end of this chapter for additional information pertaining to the use of the LOAD command. MEMORY DISPLAY MD [ []] where: Memory starting address (optional). [] Memory ending address (optional). The MD command allows the user to display a block of user memory beginning at address1 and continuing to address2. If address2 is not entered, 9 lines of 16 bytes are displayed beginning at address1. If address1 is greater than address2, the display will default to the first address. If no addresses are specified, 9 lines of 16 bytes are displayed near the last memory location accessed. EXAMPLES >MD F7D0 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F7E0 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F7F0 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F800 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F810 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F820 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F830 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F840 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ F850 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA ................ > >MD 0230 0220 0230 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................. > >MD 0200 0220 0200 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................. 0210 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................. 0220 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................. MEMORY MODIFY MM [
] CAUTION - Caution should be observed when modifying EEPROM locations. EVB MCU CONFIG register ROMON bit is cleared to disable MCU internal ROM. where:
is the memory location at which to start display/modify. The MM command allows the user to examine/modify contents in user memory at specified locations in an interactive manner. Once entered, the MM command has several submodes of operation that allow modification and verification of data. The following subcommands are recognized. CTRL J or (Space Bar) Examine/modify next location. CTRL H or A Examine/modify previous location. / Examine/modify same location. RETURN Terminate MM operation. O Compute branch instruction relative offset. If an invalid address is specified, the invalid address message "rom" is displayed on the terminal CRT> EXAMPLES DESCRIPTION >MM 0700 Display memory location 0700. 0700 44 66/ Change data at 0700 and re-examine location. 0700 66 55A Change data at 0700 and backup one location. 06FF FF AA(RETURN) Change data at 06FF and terminate MM operation. >MM 013C Display memory location. 013C F7 C18E0 51 Compute offset, result = $51. 013C F7 >MM 0200 Examine location $0200. 0200 55 80 C2 00 CE C4 Examine next location(s) using (Space Bar). MOVE MOVE [] where: Memory starting address. Memory ending address. [] Destination starting address (optional). The MOVE command allows the user to copy/move memory to new memory location. If the destination is not specified, the block of data residing from address1 to address2 will be moved up one byte. Using the MOVE command on EEPROM locations will program EPROM cells. The MOVE command is useful when programming EEPROM. As an example, a program is created in user RAM using the assemble, debugged using the monitor, and then programmed into EEPROM with the MOVE command. No messages will be displayed on the terminal CRT upon completion of the copy/move operation, only the prompt is displayed. CAUTION Caution should be observed when moving data into EEPROM locations. EVB MCU CONFIG register ROMON bit is cleared to disable MCU internal ROM. Example Description >MOVE E000 E7FF 0200 Move data from locations $E000-$E7FF to locations $0200-$09FF. > PROCEED/CONTINUE P This command is used to proceed or continue program execution without having to remove assigned breakpoints. This command is used to bypass assigned breakpoints in a program executed by the G command. NOTE Refer to example program show for the following P command example. Breakpoints have been inserted at locations $0205 and $0207 EXAMPLE DESCRIPTION >G 0200 Start execution at 0200. P-0205 Y-7982 X-FF00 A-44 B-70 C-DO S-004A Breakpoint encountered at > 0205. >P Continue execution. P-0207 Y-7982 X-FF00 A-44 B-70 C-C0 S-004A Breakpoint encountered at 0207 > REGISTER MODIFY RM [p,,x,a,b,c,s] The RM command is used to modify the MCU program counter (P), Y index (Y), X index (X), A acculmulator (A), B accumulator (B), C accumulator (C), and stack pointer (S) register contents. EXAMPLE DESCRIPTION >RM Display P register contents. P-0200 Y-798 X-FF00 A-44 B-70 C-C0 S-0054 P-0207 0220 Modify P register contents. > >RM X Display X register contents. P-C007 Y-7982 X-FF00 A-44 B-70 C-C0 S-0054 X-FF00 0220 Modify X register contents. > >RM Display P register contents. P-0220 Y0DEFE X-0220 A-DF B-DE C-D0 S-0054 P-0220 (SPACE BAR) Display remaining registers. Y-DEFE (SPACE BAR) X-0220 (SPACE BAR) A-DF (SPACE BAR) B-DE (SPACE BAR) C-DO (SPACE BAR) S-0054 SPACE BAR) (SPACE BAR) entered following stack pointer display will terminate RM command. TRACE T [] where: is the number (in hexadecimal, $1-FF max.) of instructions to execute. The T command allows the user to monitor program execution on an instruction-by-instruction basis. The user may optionally execute several instructions at a time by entering a count value (up to $FF). Execution starts at the current program counter (PC). The PC display with the event message is of the next instruction to be executed. The trace command operates by setting the OC5 interrupt to time out after the first cycle of the first opcode fetched. (*** Install Trace jumper on CMD11E9 Board to connect OC5 to XIRQ for Trace to operate ***) EXAMPLES DESCRIPTION >T SINGLE TRACE Op- 86 P-0202 Y-DEFE X-FFFF A-44 B-00 C-00 S-004B > >T 2 MULTIPLE TRACE (2) Op-B7 P-0205 Y-DEFE X-FFFF A-44 B-00 C-00 S-004B Op-01 P-0206 Y-DEFE X-FFFF A-44 B-00 C-00 S-004B > TRANSPARENT MODE TM (not available on the CME11E9 board) The TM connects the EVB host port to the terminal port, which allows direct communication between the terminal and the host computer. All I/O between the ports are ignored by the EVB until the exit character is entered from the terminal. The TM subcommands are as follows: (CTRL)A Exit from transparent mode (CTRL)B Send break to host computer. EXAMPLE DESCRIPTION >TM Enter transparent mode. . Host computer input . . (CTRL)A Task completed. Enter exit command. > Exit transparent mode. Refer to the downloading procedures at the end of this chapter for additional information pertaining to the use of the TM command. Verify VERIFY VERIFY where: compare memory to host port download data. compare memory to terminal port download data. The VERIFY command is similar to the LOAD command except that the VERIFY command instructs the EVB to compare the downloaded S-record data to the data stored in memory. EXAMPLES DESCRIPTION >VERIFY cat trial.out Enter verify command. cat trial.out done Verification completed. > >VERIFY cat trial.out Enter verify command. cat trial.out Mismatch encountered. error addr E000 Error message displaying first byte address. Refer to the downloading procedures at the end of this chapter for additional information pertaining to the use of the LOAD command. ASSEMBLY/DISASSEMBLY PROCEDURES The assembler/disassembler is an interactive assembler/editor. Each source line is converted into the proper machine language code and is stored in memory overwriting previous data on a line-by-line basis at the time of entry. in order to display an instruction, the machine code is disassembled and the instruction mnemonic and operands are displayed. All valid opcodes are converted to assembly language nmemocs. All invalid opcodes are displayed on the terminal CRT as "ILLOP". The syntax rules for the assembler are as follows: (a.) All numerical values are assumed to be hexadecimal. Therefore no base designators (e,g,, $ = hex, % = binary, etc.) are allowed. (b.0 Operands must be separated by one or more space or tab characters. (c.) Any characters after a valid mnemonic and associated operands are assumed to be comments and are ignored. Addressing modes are designated as follows: (a.) Immediate addressing is designated by preceding the address with a # sign. (b.) Index addressing is designated by a comma. The comma must be preceded a one byte relative offset (even if the offset is 00), and the comma must be followed by an X or Y designating which index register to use (e.g., LDAA 00,X). (c.) Direct and extending addressing is specified by the length of the address operand (1 or 2 digits specifies direct, 3 0r 4 digits specifies extended). Extended addressing can be forced by padding the address operand with leading zeros. (d.) Relative offsets for branch instructions are computed by the assembler. Therefore the valid operand for any branch instruction is the branch-if-true address, not the relative offset. Assembler/disassembler subcommands are as follows. If the assembler directs an error in the new source line, the assembler will output an error message and then reopen the same address location. / Assemble the current line and then disassemble the same address location. ^ Assemble the current line and then disassemble the previous sequential address location. (RETURN) Assemble the current line and then disassemble the next opcode address. (CTRL)J Assemble the current line. If there isn't a new line to assemble, then disassemble the next sequential address location. Otherwise, disassemble the next opcode address. (CTRL)A Exit the assembler mode of operation. When a new source line is assembles, the assembler overwrites what was previously in memory. If now new source line is submitted, or if there is an error in the source line, then the contents of memory remain unchanged. Each of the instruction pairs Arithmetic Shift Left (ASL)/Logical Shift Left (LSL) have the same opcode, so disassembly always displays the ASL mnemonic. If the assembler tries to assemble at an address that is not in RAM, an invalid address message "rom-xxx" is displayed on the terminal CRT (xxxx = invalid address). DOWNLOADING PROCEDURES This portion of text describes the downloading procedures. The downloading operation enables the user to transfer information from a host computer to the EVB (or target system memory) using the LOAD command. The VERIFY command is used to compare the S-record data to memory data. Specific downloading procedures are described enabling the user to IBM Personal Computer (PC) host computer system. Downloading operations are accomplished utilizing the TM and LOAD commands. The TM (Transport Mode) command connects the EVB host port to the terminal port, which allows direct communication between the terminal and host computer. All I/O between the ports are ignored by the EVB until the exit command (CTRL)A is entered from the terminal. The LOAD command moves data information in S-record format (see Appendix A) from an external host computer to the EVB user RAM. The following pages provide examples and descriptions of how to perform downloading operations in conjunction with an IBM PC host computer. Prior to performing any IBM PC operation, ensure that both IBM PC and EVB baud rates are identical. NOTE IBM PC to EVB interconnection is accomplished by a single RS-232C cable assembly. This cable is connected to the EVB terminal I/O port connector COM1 for downloading operations. To perform the IBM PC to EVB downloading procedure, perform/observe the following: EXAMPLE DESCRIPTION C>KERMIT IBM PC prompt. Enter KERMIT IBM-PC Kermit-MS VX.XX program. Type ? for help Kermit-MS>SET BAUD 9600 Set IBM PC baud rate. Kermit-MS>-CONNECT Connect IBM PC to EVB. [Connecting to host, type Control-] C to return to PC] (RETURN) >LOAD T EVB download command (via terminal port) entered. (CTRL)]C Kermit-MS>PUSH The IBM Personal Computer DOS Version X.XX (C)Copyright IBM Corp 1981, 1982, 1983 C>TYPE (File Name) > COM1 Motorola S-record file name. C>EXIT S-record downloading completed. Kermit-MS>CONNECT Return to monitor BUFFALO program. >(CTRL)]C Kermit-MS>EXIT Exit Kermit program. APPENDIX A S-RECORD INFORMATION INTRODUCTION The Motorola S-record format was devised for the purpose of encoding programs or data files in a printable format for transportation between computer systems. This transportation process can therefore be monitored and the S-records can be easily edited. S-RECORD CONTENT When observed, S-records are essentially character strings made of several fields which identify the record type, record length, memory address, code/data, and checksum. Each byte of binary data is encoded as a 2-character hexadecimal number: the first character representing the high-order 4 bits, and the second the low-order 4 bits of the byte. Five fields which compromise an S-record are shown below: TYPE RECORD LENGTH ADDRESS CODE/DATA CHECKSUM where the fields are composed as follows: PRINTABLE FIELD CHARACTERS CONTENTS Type 2 S-record type - S0, S1, etc. Record 2 Character pair count in the record, length excluding the type and record length. Address 4,6, 2-, 3-, or 4-byte address at which or 8 the data field is to be loaded into memory. Code/data 0-2n From 0 to n bytes of executable code, memory loadable data, or descriptive information. For compatibility with teletypewriters, some programs may limit the number of bytes to as few as 28 (56 printable characters in the S- record. Checksum 2 Least significant byte of the one's complement of the sum of the values represented by the pairs of characters making up the record length, address, and the code/data fields. Each record may be terminated with a CR/LF/NULL. Additionally, an S- record may have an initial field to accommodate other data such as line numbers generated by some time-sharing systems. Accuracy of transmission is ensured by the record length (byte count) and checksum fields. S-RECORD TYPES Eight types of S-records have been defined to accommodate the several needs of the encoding, transportation, and decoding functions. The various Motorola upload, download, and other record transportation control programs, as well as cross assemblers, linkers, and other file- creating or debugging programs, utilize only those S-records which serve the purpose of the program. for specific information on which S-records are supported by a particular program, the user manual for that program must be consulted. NOTE The EVB monitor supports only the S1 and S9 records. All data before the first S1 record is ignored. Thereafter, all records must be S1 type until the S9 record terminates data transfer. An S-record format may contain the following record types: S0 Header record for each block of S-records. The code/data field may contain any descriptive information identifying the following block of S-records. The address field is normally zeroes. S1 Code/data record and the 2-byte address at which the code/data is to reside. S2-S8 Termination record for a block of S1 records. Address fields may optionally contain the 2-byte address of the instruction to which control is to be passed. If not specified, the first entry point specification encountered in the input will be used. There is no code/data field. Only one termination record is used for each block of S-records. Normally, only one header record is used, although it is possible for multiple header records to occur. S-RECORD CREATION S-record format programs ma be produce by several dump utilities, debuggers, or several cross assemblers or cross linkers. Several programs are available for downloading a file in S-record format from a host system to an 8-bit or 16-bit microprocessor-based system. S-RECORD EXAMPLE Shown below is a typical S-record format, as printed or displayed: S00600004844521B S1130000285F245F2212226A000424290008237C2A S11300100002000800082629001853812341001813 S113002041E900084E42234300182342000824A952 S107003000144ED492 S9030000FC The above format consists of an S0 header record, four S1 code/data records, and an S9 termination record. The S0 header record is comprised of the following character pairs: S0 S-record type S0, indicating a header record. 06 Hexadecimal 06 (decimal 06), indicating six character pairs (or ASCII bytes) follow. 00 Four-character 2-byte address field, zeroes. 00 48 44 ASCII H, D, and R - "HDR". 52 1B Checksum of SO record. The first S1 code/data record is explained as follows: S1 S-record type S1, indicating a code/data record to be loaded/verified at a 2-byte address. 13 Hexadecimal 13 (decimal 19), indicating 19 character pairs, representing 19 bytes of binary data, follow. 00 Four-character 2-byte address field; hexadecimal address 0000, 00 indicates location where the following data is to be loaded. The next 16 character pairs are the ASCII bytes of the actual program code/data. In this assembly language example, the hexadecimal opcodes of the program are written in sequence in the code/data fields of the S1 records; OPCODE INSTRUCTION 28 5F BHCC $0161 24 5F BCC $0163 22 12 BHI $0118 22 6A BHI $0172 00 04 24 BRSET 0,$04,$012F 29 00 BHCS $010D 08 23 7C BRSET 4,$23,$018C . (Balance of this code is continued in the code/data fields . of the remaining S1 records, and stored in memory location . 0010, etc..) 2A Checksum of the first S1 record. The second and third S1 code/data records each also contain $13 (19) character pairs and are ended with checksums 13 and 51, respectively. The fourth S1 code/data record contains 07 character paris and has a checksum of 92. The S9 termination record is explained as follows: S9 S-record type S9, indicating a termination record. 03 Hexadecimal 03, indicating three character pairs (3 bytes) follow. 00 Four-character 2-byte address field, zeroes. 00 FC Checksum of S9 record. Each printable character in an S-record is encoded in hexadecimal (ASCII in this example) representation of the binary bits which are actually transmitted. For example, the first S1 record above is sent as shown below. type length address code/data checksum S 1 1 3 0 0 0 0 2 8 5 F 2 A 53 31 31 33 30 30 30 30 32 38 35 46 32 41 TEXT MESSAGES What? Too Long Full Op- rom- Command? Bad Argument No host port available done checksum error error addr ERROR MESSAGES FOR ASSEMBLER Immediate mode illegal Error in mnemonic table Illegal bit op Bad argument Mnemonic not found Unknown addressing mode Indexed addressing assumed Syntax error Branch out of range